Knutson Marine is a full service marina with multiple locations to better suit our customer’s needs. Our factory authorized technicians are trained to do professional grade work. We are also a Yanmar Marine Certified Dealer / Service Center and are able to provide exclusive factory authorized service and warranty work.
OUTBOARD ENGINE SERVICES – OUTBOARD WINTERIZATION & OIL CHANGE
- • Add fuel stabilizer
- • Run the engine to temperature, flush with fresh water, fog engine with rust preventive oil mixture.
- • Drain gearcase, inspect for impurities and refill.
- • Change crankcase oil and filter.
- • Change the remote fuel/water separator filter.
- • Remove and inspect the propeller, lubricate the shaft, and re-install.
- • Lubricate all engine grease fittings, and inspect and replace zincs as needed.(propeller reconditioning is additional if needed).
- • Disconnect battery cables, clean and lubricate terminals.
- • Reset all maintenance parameters.
OUTBOARD WINTERIZATION, PREVENTIVE MAINTENANCE & WATER PUMP IMPELLER
- • All services included in standard winterization.
- • Run the boat and check engine for proper function.
- • Remove the lower unit and install new water pump impeller and gaskets and inspection of wear plates and housing.
- • Replace all engine fuel filters (other than V.S.T. filter).
- • Pressure check your gear case.
- • Check operation of the power trim pump.
- • Spray the entire engine with rust inhibitor.
- • Touch-up the paint on the lower gear case as needed.
OUTBOARD TUNE-UP
- • Check cylinder compression.
- • Install new spark plugs.
- • Replace all engine fuel filters (other than V.S.T. filter).
- • Check and adjust timing at idle.
- • Check and adjust throttle and shift linkages.
- • Check for proper adjustment of the engine oil injection system and
- • Check engine electrical wiring.
- • Lubricate all linkages.
- • Run a computer diagnostic analysis to check all manufacturers’ specifications on 4 stroke, Optimax, & H.P.D.I. engines.
- • Reset all maintenance parameters.
INBOARD/OUTBOARD ENGINE SERVICES I/O ENGINE WINTERIZATION with PREVENTIVE MAINTENANCE
- • Check all systems including oil pressure, charging system, and water temperature including flushing scale from engine petcocks.
- • Change your oil, oil filter, and fuel/water separator filter.
- • Check fluid levels on power steering, power trim, and trim tabs pumps.
- • Inspect all engine hoses and fuel lines, lubricate all linkages, inspect and replace engine zincs as needed, inspect all drive belts, and touch up paint.
- • Add fuel stabilizer, run the engine and flush with fresh water.
- • Drain, run antifreeze thru, and fog the engine with a rust preventative oil mixture and coat the engine with rust inhibitor to prevent corrosion.
- • Disconnect battery cables, clean and lubricate terminals (Fuel is additional).
I/O ENGINE TUNE-UP
- • Check the cylinder compression.
- • Install new distributor cap, rotor/sensor assembly, spark plugs, P.C.V. valve, and all engine fuel filters.
- • Clean the flame arrestor; check the timing, the idle speed and the control adjustments.
- • Perform computer diagnostic analysis to check all manufacturers’ specifications.
RAW WATER PUMP REBUILD
- • Includes removal and replacement of water pump impeller, gaskets, and wear plates.
OUTDRIVE WINTERIZATION with PREVENTIVE MAINTENANCE
- • Remove the outdrive, lubricate the gimbal housing, universal, and tail shaft (old style Volvo is not removed).
- • Drain the gear case, inspect the fluid for impurities and refill the gear case.
- • Remove and inspect the propeller, lubricate the shaft and re-install propeller.
- • Lubricate steering, pivot, and shift cables, re-torque gimbal ring to steering shaft connection.
- • Inspect all bellows and hoses. (On Mercruiser Alpha drive – We install a new water pump impeller, wear plate, and gaskets).
- • Pressure test the outdrive.
- • Clean the shift cavity and all internal water passages.
- • Check the gimbal bearing and alignment and touch up the paint.
- • Inspect and replace all outdrive zincs as needed.
- • Replace the outdrive gasket and o-ring kit, and re-install (propeller reconditioning if needed will be billed additionally).
INBOARD ENGINE SERVICES INBOARD ENGINE WINTERIZATION WITH PREVENTIVE MAINTENANCE
- • Check all engine systems including oil pressure, charging system, and water temperature including flushing scale from engine petcocks.
- • Change oil, oil filter, and fuel/water separator filter.
- • Check fluid levels on power steering, power trim, and trim tab pumps, inspect all engine hoses and fuel lines, lubricate all linkages, inspect and replace engine zincs as necessary, inspect all drive belts, touch up paint.
- • Add fuel stabilizer, run the engine and flush with fresh water.
- • Drain, run anti-freeze through, & fog the engine with rust preventive oil mixture, & coat engine with rust inhibitor to prevent corrosion.
- • Disconnect Battery cables, clean and lubricate terminals. (Fuel is additional).
INBOARD ENGINE TUNE-UP
- • Check cylinder compression, install new distributor cap, rotor/sensor assembly, spark plugs, PCV valve, and all engine fuel filters.
- • Clean flame arrestor, check timing, idle speed, and the control adjustments.
- • Perform computer diagnostic analysis to check all manufacturers’ specifications.
INBOARD RAW WATER PUMP REBUILD
- • Includes removal and replacement of impeller and gaskets and inspection of wear plates and housing.
DIESEL SERVICES DIESEL ENGINE WINTERIZATION with PREVENTIVE MAINTENANCE
- • Change the engine oil and oil filter, and inspect for any leaks.
- • Change all the fuel filters, filter elements, and coolant filters.
- • Check coolant with refract meter.
- • Inspect all belts, hoses, and fuel lines.
- • Replace any air filters as needed.
- • Add fuel stabilizer and flush the engine with antifreeze.
- • Spray the entire engine with rust inhibitor to prevent corrosion and seal out water during storage.
- • Inspect and replace engine zincs as needed (zincs charged additionally as necessary).
- • Optional impeller service: (See Raw Water Pump Rebuild Below).
RAW WATER PUMP REBUILD
- •Includes removal and replacement of impeller and gaskets and inspection of wear plates and housing.
DIESEL TRANSMISSION WINTERIZATION with PREVENTIVE MAINTENANCE
- • Drain the oil, inspect for impurities, refill, change the filter, and just and lubricate the linkages
- • Visually inspect the propeller shaft, strut, and cutlass bearing
IPS POD DRIVE SERVICES IPS POD DRIVE WINTERIZATION with PREVENTIVE MAINTENANCE
- • Drain the oil, inspect for impurities, refill, change the filter, check power steering fluid, change zinc, remove and visually inspect the propellers and shafts, lubricate and reinstall.
SPRING COMMISSIONING
- • Charge batteries, start engine and check all operating systems
- • Sea trial boat and verify proper wide open throttle and RPM’s
- • Check all boat and engine gauges and all warning alarms
- • Check and adjust steering torque, control cables and belt tension
- • Evaluate the electrical system including checking for proper operation of bilge blower, bilge pumps, navigation lights, cabin and dash lights, salt water washdown, baitwell system, icemaker, air conditioning, and 110v dockside power
- • Repair-related parts and labor are additional
WASH, WAX & DETAIL
- • Wash, wax, and detail your entire boat including hull sides and deck
- • Clean bilge area, glass, and oil any outside woodwork
- • Vacuum inside, clean and “Armor All” cockpit vinyls, polish rails, and lubricate canvas snaps
ACCESSORY SERVICES
- • Electronics work
BODY WORK/COSMETIC SERVICES
- • Fiberglass and gel coat repair
- • canvas repair and installation
- • custom painting
- • Wash, wax and detai
INSURANCE
- • Provide insurance estimates
- • Follow up with your insurance company